-40%
Set of Crossover PCBs for the Slipstream DIY speaker design - PCB Kit
Set of Crossover PCBs for the Slipstream DIY speaker design - PCB Kit
Set of Crossover PCBs for the Slipstream DIY speaker design - PCB Kit

Set of Crossover PCBs for the Slipstream DIY speaker design - PCB Kit

$ 11.61

Availability: 10 in stock
  • Restocking Fee: No
  • Return shipping will be paid by: Seller
  • All returns accepted: Returns Accepted
  • Type: Crossover
  • Condition: New
  • Refund will be given as: Money back or replacement (buyer's choice)
  • Item must be returned within: 30 Days
  • Compatible Model: Slipstream
  • Compatible Brand: DIY
  • Brand: Unbranded

    Description

    Custom printed circuit boards designed for the crossover of the Slipstream DIY speaker design.
    These boards makes crossover assembly quick and easy!
    This kit includes the three crossover circuit boards required for a *
    single speaker*
    .
    The boards feature large solder pads and copper traces for great electrical connectivity.
    Note photos of fully assembled crossovers are for reference only.
    Includes:
    1x Low frequency / Woofer crossover board for the Slipstream DIY speaker design.  Measures 3" x 5".
    1x Mid frequency / Midrange crossover board for the Slipstream DIY speaker design.
    Measures 3" x 7.5"
    1x High frequency / Tweeter crossover board for the Slipstream DIY speaker design. Measures 3" x 8.875"
    6x Terminal blocks which accept up to 12 gauge bare wire.
    14x Snap in PCB standoffs.
    14x Mounting screws (screw finish may vary).
    Requires:
    Crossover components for the Slipstream speaker design.
    Compatible components tested for fit on this PCB listed below, other components of identical value may fit but verify dimensions are similar to the components listed.
    Components required for the Slipstream Design:
    C1 / C2 -
    50uF - 100v Non-Polarized Capacitor
    C3 -
    400uF - 100v Non-Polarized Capacitor
    C4 / C6
    - 12uF - Dayton Audio DMPC-12
    C5
    -
    68uF - 100v Non-Polarized Capacitor
    C7
    -
    5.6uF - 100v Non-Polarized Capacitor
    C8
    - 4.3uF - Dayton Audio DMPC-4.3
    C9
    - 5.6uF - Dayton Audio DMPC-5.6
    C10
    - 1.2uF or (1uF + 0.22uF) - Erse MPX25-03-1.20 or (
    Dayton Audio DMPC-1 +
    Dayton Audio DMPC-0.22)
    C11
    - 2.2uF - Dayton Audio DMPC-2.2
    L1 -
    6.0mH - Erse 6.0mH 18 AWG I Core -or- Dayton Audio 6.0mH 18 AWG I-Core
    L2 -
    Dayton Audio 0.20mH 20 AWG Air Core
    L3 -
    Dayton Audio 2.0mH 20 AWG Air Core
    L4 -
    Dayton Audio 0.70mH 20 AWG Air Core
    L5 -
    Dayton Audio 0.40mH 20 AWG Air Core
    L6 -
    Dayton Audio 0.30mH 20 AWG Air Core
    L7 -
    Dayton Audio 0.80mH 20 AWG Air Core
    L8 -
    Dayton Audio 0.90mH 20 AWG Air Core
    R1/R2 -
    3 Ohm - Dayton Audio DNR-1.0
    R3/R4
    - 30 Ohm - Dayton Audio DNR-1.0
    R5/R6
    - 16 Ohm - Dayton Audio DNR-1.0
    R7
    - 8 Ohm - Dayton Audio DNR-1.0
    R8
    - 2.7 Ohm - Dayton Audio DNR-1.0
    R9
    - 12.5 Ohm - Dayton Audio DNR-1.0
    R10
    - 20 Ohm - Dayton Audio DNR-1.0
    R11
    - 0.33 Ohm - 5w Resistor Wire Wound
    Assembly:
    Glue components to the correct positions on the board (hot melt glue works great). Secure inductors with non metallic cable ties. Solder components leads to the pads on the bottom of the board. Attach wires from input and drivers to the crossover. Insert standoffs into the bottom of the board at the four corners and mount the crossover to the enclosure.